Gus Green Gus Green's Profile Page

Gus Green Gus Green

0 Course Enrolled • 0 Course Completed

Biography

NS0-093 Updated Testkings, Exam NS0-093 Tests

How far the distance between words and deeds? It depends to every person. If a person is strong-willed, it is close at hand. I think you should be such a person. Since to choose to participate in the Network Appliance NS0-093 certification exam, of course, it is necessary to have to go through. This is also the performance that you are strong-willed. Prep4sureGuide Network Appliance NS0-093 Exam Training materials is the best choice to help you pass the exam. The training materials of Prep4sureGuide website have a unique good quality on the internet. If you want to pass the Network Appliance NS0-093 exam, you'd better to buy Prep4sureGuide's exam training materials quickly.

Network Appliance NS0-093 exam is an essential certification for individuals looking to gain expertise in NetApp storage hardware support. It assesses a candidate’s knowledge and skills in identifying and troubleshooting hardware issues in the NetApp environment. NS0-093 Exam is computer-based and can be taken at any Pearson VUE testing center globally. Passing the NS0-093 exam is a testament to an individual’s expertise in NetApp hardware support and can help advance their career in the IT industry.

>> NS0-093 Updated Testkings <<

Exam NS0-093 Tests & NS0-093 Test Simulator Free

The point of every question in our NS0-093 exam braindumps is set separately. Once you submit your exercises of the NS0-093 learning questions, the calculation system will soon start to work. The whole process only lasts no more than one minute. Then you will clearly know how many points you have got for your exercises of the NS0-093 study engine. And at the same time, our system will auto remember the wrong questions that you answered and give you more practice on them until you can master.

Network Appliance NetApp Accredited Hardware Support Engineer Sample Questions (Q58-Q63):

NEW QUESTION # 58
You have created a case with NetApp Support for an issue with a DS4246 shelf on an ONTAP 9.12.1 system.
They have requested that you provide shelf logs.
What action do you need to take to collect the shelf logs?

A. Invoke a diagnostic AutoSupport with the subsystem storage.
B. Invoke an autosupport of type all using Active IQ Unified Manager.
C. Invoke a diagnostic autosupport with the subsystem log_files.
D. Provide the output of the nodeshell command rdfile/etc/log/shelflog.

Answer: A

Explanation:
To collect shelf logs for a DS4246 shelf in an ONTAP 9.12.1 system, you must invoke a diagnostic AutoSupport specifically targeting the storage subsystem. This action ensures that detailed storage logs, including shelf logs, are included in the AutoSupport bundle.
* Use the following command:
Steps to Collect Shelf Logs:bash
Copy code
system node autosupport invoke -node <node_name> -type diagnostic -subsystem storage Replace <node_name> with the name of the node experiencing the issue.
* This command generates an AutoSupport message that includes logs related to storage subsystems, such as disk shelves and adapters.
* Provide the AutoSupport case number to NetApp Support for further analysis.
* A. Provide the output of the nodeshell command rdfile /etc/log/shelflog:
* While this command allows manual reading of shelf logs, it is not a recommended or comprehensive approach for collecting logs for NetApp Support cases.
* B. Invoke an AutoSupport of type all using Active IQ Unified Manager:
* This action generates a generic AutoSupport bundle, which may not include detailed shelf logs unless explicitly targeted.
* D. Invoke a diagnostic AutoSupport with the subsystem log_files:
* The log_files subsystem targets general system logs, not storage-specific logs like shelf logs.
Why Other Options Are Incorrect:
* "ONTAP 9 AutoSupport and Diagnostics Guide" outlines the use of the subsystem storage option for collecting shelf logs.
* The "Troubleshooting Storage Subsystems" documentation specifies diagnostic AutoSupport as the method for gathering shelf-related logs.
References:

NEW QUESTION # 59
On a NetApp FAS9000 system, which two field replaceable units (FRUs) are supported for replacement without takeover? (Choose two.)

A. NVRAM module
B. DCPM module
C. I/O module
D. caching module

Answer: A,C

Explanation:
FRUs on FAS9000 Supporting Replacement Without Takeover:
* A (I/O Module): I/O modules can be replaced hot (without takeover) to maintain system uptime during hardware servicing.
* D (NVRAM Module): NVRAM modules on FAS9000 can also be replaced without a node takeover, ensuring data integrity during replacement.
Why Other Options Are Incorrect:
* B (DCPM Module): The DCPM (Data Center Power Management) module is not hot-swappable and requires a node takeover.
* C (Caching Module): The caching module is integrated and typically requires a node takeover or power-down for replacement.
NetApp Reference Documentation:
* Refer to the "NetApp FAS9000 Hardware Service Guide" for supported FRU replacement procedures and operational constraints.

NEW QUESTION # 60
You are replacing a boot device on a FAS8300 system that is running ONTAP 9.10P6 software. You attach a USB memory stick to the external USB port on the storage controller but cannot access the memory stick.
What step needs to be performed to access the boot device?

A. Set the port to "enabled" with setenv.
B. Add the boot device before the BIOS is loaded.
C. You need to use ONTAP 9.11 or later software.
D. The external USB port is not activated on NetApp systems.

Answer: A

Explanation:
When replacing a boot device on a FAS8300 system and using a USB memory stick for recovery or installation, the external USB port must be explicitly enabled. This is done through the setenv command in the boot environment.
* Reboot the system and interrupt the boot process to access the bootloader prompt.
* At the bootloader prompt, use the following command:
Steps to Enable the External USB Port:arduino
Copy code
setenv usbport_enabled true
* Save the configuration and proceed with the boot process.
* B. You need to use ONTAP 9.11 or later software:
* ONTAP 9.10P6 fully supports external USB recovery. There is no need to upgrade to ONTAP
9.11 for this functionality.
* C. Add the boot device before the BIOS is loaded:
* While the USB device must be inserted during the boot process, this alone will not enable access unless the port is enabled via setenv.
* D. The external USB port is not activated on NetApp systems:
* This is incorrect. The external USB port is supported but must be explicitly enabled in the bootloader environment.
Why Other Options Are Incorrect:
* NetApp Hardware Installation Guide for FAS8300 systems outlines the steps for enabling the USB port during recovery.
* "ONTAP Boot Troubleshooting Guide" specifies the use of the setenv command to activate USB ports.
References:

NEW QUESTION # 61
Which two steps are required to replace a drawer in a DS460c shelf? (Choose two.)

A. Disconnect the cable chains from the chassis.
B. Power off the shelf.
C. Evacuate all drives in the drawer.
D. Shut down both nodes.

Answer: A,C

NEW QUESTION # 62
During an ONTAP upgrade, nodeA1 fails to boot. You notice that it is loading the previous version of ONTAP software. What step can be taken to boot the node successfully?

A. From the clustershell of nodeA1, run system node image modify to point to the correct version of ONTAP software.
B. From the loader prompt of nodeA1, run boot_backup to run the correct version of ONTAP software.
C. From the loader prompt of nodeA1, use setenv GX_PRIMARY_KERNEL_URL to point to the correct version of ONTAP software.
D. From the clustershell of the partner, run system node image modify to point to the correct version of ONTAP software.

Answer: C

Explanation:
When a node fails to boot and loads the previous version of ONTAP, it usually indicates that the primary boot location is incorrect. To resolve this:
* Enter the LOADER Prompt:
* Interrupt the boot process to access the LOADER prompt.
* Set the Primary Kernel URL:
* Use the following command:
Steps to Boot the Correct ONTAP Version:setenv GX_PRIMARY_KERNEL_URL
<URL_to_correct_ONTAP_version>
* Boot the Node:
* Run the boot command to load the correct version.
* B. From the loader prompt of nodeA1, run boot_backup:
* Booting the backup image may result in an outdated version of ONTAP, not the desired version.
* C. From the clustershell of the partner, run system node image modify:
* Modifications to the ONTAP image must be done from the LOADER prompt, not the clustershell.
* D. From the clustershell of nodeA1, run system node image modify:
* NodeA1 cannot load ONTAP, so this command cannot be run.
Why Other Options Are Incorrect:
* "ONTAP System Boot Guide" explains how to resolve boot issues using the LOADER prompt.
* NetApp documentation on environment variables includes the use of GX_PRIMARY_KERNEL_URL.
References:

NEW QUESTION # 63
......

It is acknowledged that there are numerous NS0-093 learning questions for candidates for the exam, however, it is impossible for you to summarize all of the key points in so many materials by yourself. But since you have clicked into this website for NS0-093 practice materials you need not to worry about that at all because our company is especially here for you to solve this problem. We have a lot of regular customers for a long-term cooperation now since they have understood how useful and effective our NS0-093 Actual Exam is. So will you!

Exam NS0-093 Tests: https://www.prep4sureguide.com/NS0-093-prep4sure-exam-guide.html